Hardware-Hilfe für User Grundsätze
Grundsätze bei arbeiten an Hardware:
- Netzstecker ziehen, PC nochmal einschalten (wg, Restspannung, am MB von ASUS A7V ist z.B. dazu eine Leuchtdiode neben dem AGP-Port), an allen Geräten nur Spannungsfrei arbeiten!
- Feuchtigkeit immer fernhalten! Staubige Slots (z.B. PCI) einfach mit trockenem Pinsel (einer der keine Haare verliert!) reinigen
- Speicher + CPU, immer nur geerdet anfassen, ansonsten wars das für die Teile!
Einfach langes Kabel am Gehäuse fest schrauben (Ende abisolieren + um Schraube) + ums Handgelenk ebenfalls abisolierte Ende
Nachtrag: länge entsprechend Arbeitsbereich; Erdung, falls man doch mal auf die Buskontakte kommt;- Mainboard (od. Motherboard) immer das Handbuch dazu nehmen, od. vorher Beschreibung von der HP des Herstellers ziehen
- Jumper, od. Switches für CPU-Taktung immer 2x kontrollieren!
- Kühlleitpaste für CPU immer hauchdünn! auftragen, sonst keine Kühlung!
- GraKa und Lüfter nicht immer möglich, daher gibts auch Kühlpads!
Legende:
MB= Mainboard/ Motherboard
CPU= Hauptprozessor, z.B. AMD, Pentium
Jumper= Brücke auf Stiftkontakten
Switches= selbe wie Jumper, nur als Schalter (Switch=gibts auch als Umschalter für Monitor, Tastatur, usw..)
HP= Homepage
Speicher= RAM, SD-RAM, EDO-RAM, DDR-RAM
AGP= spezieller Steckplatz für Grafik-Karten (=GraKA)
- Bios updates Vorgang:
Dateien auf Diskette, PC im Dos mit Bootdieskette starten, *.exe Datei betätigen (z.B. Amiflash.exe für AMIBIOS). Altes Bios abspeichern! Falls Fehler aufgetreten sind!!!
Dazu sollte vorher das Passwort entfernt sein, sonst kanns zu Problemen kommen, wenn man wieder ins Bios will!
Wenn dies der Fall sein sollte, dann Batterie vom Mainboard kurz trennen (einfach nen Stück Plastikklebeband od. so kurz unter den oberen Kontakt schieben), danach sind alle Bios Einstellung, sowie Passwort (gelöscht) auf default gesetzt.
- Es sollten nur die aktuellsten Treiber verwendet werden, für AGP GraKa empfehle ich DirectX 7.0A (läuft nach meiner Erfahrung mit den geringsten Problemen, auch mit älteren Karten)!
Hoffe das hilft! :okay:
Kommende Themen:
- Einstellungen der Laufwerke (Master, Slave, Cable-Select)
- AGP - Port
- Cross-Over Kabel selbst gemacht
Nachtrag:
Tip: Bei Piep-Tönen, sobald der PC eingeschaltet wird, liegts meistens an Speichermodulen, die nicht richtig sitzen!
Hardware-Hilfe für User die 2.
Fange diesmal mit dem Cross-Over Kabel an. :okay:
Jeder, der ein Heimnetzwerk betreibt, kennt das Problem! Kabel, kein Problem, aber wie krieg ich den Stecker durch die Wand??? :wall: Man will ja schließlich keinen Mauerdurchbruch fabrizieren! :grr:
Also, kurzerhand selbst gebastelt! :denk: *Wie geht das denn?*
Benötigtes Material:
1. Spannungsmessgerät (mit Widerstandsmessung Kabel überprüfen, auch durch-, od. abklingeln genannt)
2. Crimpzange für RJ45 Stecker (kann man sich auch leihen)
3. RJ45 Stecker
4. Kabel CAT 5 (Patch od. Twisted Pair auch genannt) 8 adrig mit Abschirmung
5. evtl. Bohrmaschine (falls noch kein Loch inner Wand :oD )
Tips: Meistens sind fertige Patch-Kabel günstiger, da brauch man dann nur einen Stecker neu zu machen!
Weiterhin bitte Kabel durch die Wand verlegen, bevor Ihr den neuen Stecker anbringt, und nicht vergessen die "Tülle" (Abdeckung vom Stecker) vor dem abisolieren (bis auf die Abschirmung, ca. 2-3cm länge) draufschieben! Sonst ärgert Ihr Euch hinterher weil Ihrs vergessen habt, und noch nen Stecker braucht! :sauer:
Zur Steckerbelegung (Kabel sind teilweise verschiedenfarbig):
1/3
2/6
3/1
4/4
5/5
6/2
7/7
8/8
Die Nummern stehen für den Kontakt an den Steckern. Ich empfehle Stecker, die mit einem Blech versehen sind für die Abschirmung!
Die Kabellänge sollte eigentlich nicht 15m überschreiten, aber ich hab hier auch nen 20m Kabel das funzt! :oD
Sollte knickfrei verlegt werden, um Kabelbruch zu vermeiden!
Beim crimpen ist zu beachten:
1. Tülle vorher aufgeschoben
2. abisoliert wird nur die äußerste Kabelhülle bis auf die Abschirmung (evtl. diese etwas kürzen)
3. Adern bis zum Anschlag in den Stecker schieben, sonst kein Kontakt!
4. Crimpzange genau ansetzen, Stecker unter dauerndem einschieben des Kabels crimpen!
5. zur Kontrolle danach durchklingeln!
So, das wars, mache weiter wenn Zeit habe! :smoke:
PS: Jetzt fragt mich bitte nicht, wie Ihr nen Loch durch die Wand hinkriegt oder sowas! :wall: *Plöde Wand! GRRRR!!*
Nachtrag: @Admin, od. Mod bitte nach oben verschieben, wenn möchlisch? :sceptic:
RE: Hardware-Hilfe für User
respekt das jemand so viel geschrieben hat um andere user vor schaden zu bewaren.Ich weis zwar das das viel arbeit ist und ich will dir arbeit bestimmt auch nicht nider machen aber wer ahnung hat und weis was er tut braucht solche hinweise nicht weil er sie sowieso kennt und die meisten sowieso missachtet.
Und wer keine ahnung hat solte das sowieso "profies" machen Lassen.
aber trotzten respekt,respekt für die viele arbeit
PS.:das sollte keine kritik sein sonder nur eine anmerkung meinerseits